ocxo (o ven c ontrolled c rystal o scillators) +5.0v; +12v OC30T series hcmos square wave mercury since 1973 mercury www.mercury-crystal.com taiwan: tel (886)-2-2406-2779, fax (886) -2-2496-0769, e-mail: sales-tw@mercury-crystal.com u.s.a.: tel (1)-909-466-0427, fax (1 )-909-466-0762, e-mail: sales-us@mercury-crystal.com mercury page 1 of 2 date: dec. 1, 2006 rev. 1 mercury OC30T is 36.2x27.2 mm 5 pin solder sealed metal pacakge with 25.4x17.8 mm pin-to-pin spacin g high stability low aging ocxo. besides standard at cut crystal, users can also choose sc cut crystal for better performance. 50 ohm load sine output is available as oc30e series. for same package size but with standard eurocase ocxo pin configurations, please refer to oc31t series. general specifications ( 10 mhz at+25c, at specified vcc and +2.5 v vcon) output wave form hcmos square wave. wave form code is ? t ? frequency range 1.25 mhz ~100.0 mhz type of crystal cut used at -cut. use ? a ? for crystal code or sc- cut: use ? s ? for crystal code. sc has better performance but higher cost. see technical note tn-031. supply voltage (vcc) +5.0 v d.c 5% (voltage code is ? 5 ?); +12.0 v d.c 5% (voltage code is ? 12 ?) initial calibration tolerance 0.5 ppm max. at time of shipment; vcon=+2.5v, at +25c best stability 0c to +60c -20c to +70c -40c to +85c for at crystal 0.03 ppm 0.08 ppm 0.2 ppm operating temperature range (custom spec. on request) for sc crystal 0.01 ppm 0.02 ppm 0.03 ppm aging (after 72 hours of continuous operation) at :3 ppb max./day; 0.5 ppm max./first year;3 ppm max. over 10 years. sc : 2 ppb max./day; 0.1 ppm max./first year;0.5 ppm max. over 10 years. supply voltage 5% variation 20 ppb max. load 5% variation: 20 ppb max. frequency stability vs warm-up time (at +25c) at : 3 minutes max. within 0.5 ppm of its reference frequency. sc : 1 minute max. within 0.1 ppm of its reference frequency. freq. deviation range at : 5 ppm min. 20 ppm max.; sc : 0.5 ppm min, 2 ppm max. referenced to fo at +25c and over operating temperature range. control voltage range 2.5 v 2.0 v transfer function positive: increasing control volt age increases output frequency. voltage control on pin 1 (efc) (electronics frequency tuning) input impedance 100 k ohms min. efc linearity 10% max. power power dissipation (at +25c) 1.2 watts max. at steady-state; 3.5 watts max. at turn-on. load (fan out) 15 pf hcmos max. duty cycle (measured at 50%vcc) 50% 10% output voltage logic high (v oh ) +4.5 v min. output voltage logic low (v ol ) +0.5 max. rise and fall time 5 ns max. (measured at 20% ? 80% of waveform) reference voltage output +4.0 v d.c 0.3 v d.c . or custom. offset 1 hz 10 hz 100 hz 1 khz 10 khz 10 mhz at-cut xtal -75 dbc -100 dbc -130 dbc -140 dbc -150 dbc output phase noise 10 mhz sc-cut xtal -85 dbc -120 dbc -140 dbc -145 dbc -150 dbc storage temperature -55c to +125c shock 2000 g?s, 0.3 ms ? sine vibration 10 to 2000 hz / 10 g?s
ocxo (o ven c ontrolled c rystal o scillators) +5.0v; +12v OC30T series hcmos square wave mercury since 1973 mercury page 2 of 2 date: dec. 1, 2006 rev. 1 + - 0.1uf v a - + vcc - + vcon bottom view oscilloscope frequency counter 15 pf 50% 20% 80% tr tf t2 t1 duty cycle = t1 t2 *100% * * include probe, fixture and stray capacitances OC30T test circuit OC30T series package dimensions and pin connections : unit mm pin 1: voltage control efc pin 2: gr ound, case pin 3: rf output pin 4: reference voltage output pin 5: supply voltage part number format and example : example : OC30T5s-10.000-0.01/-20+70 oc 30 t 5 s ? 10.000 ? 0.01 -20+70 n o p q r dash s dash t slash u n : ? oc ? product prefix for ocxo o : package type. ? 30 ? for oc30 package p : output wave form code. ? t ? for hcmos square wave output.. q : supply voltage code. ? 5 ? for +5.0v; ? 12 ? for +12.0v r : crystal type. use ? a ? for at-cut crystal; use ? s ? for sc-cut crystal. s : frequency in mhz; t : frequency stability in ppm; u : operating temperature range: -20 c to +70 c in this case.
|
